high efficiency rectifier voltage range 50 to 1000 volts current 1.0 ampere rectron semiconductor technical specification features * low power loss, high efficiency * low leakage * low forward voltage * high current capability * high speed switching * high surge capability * high reliability mechanical data * case: molded plastic * epoxy: device has ul flammability classification 94v-o * lead: mil-std-202e method 208c guaranteed * mounting position: any * weight: 0.33 gram maximum ratings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. electrical characteristics (at t a = 25 o c unless otherwise noted) rl101h thru rl108h a-405 maximum ra tings (at t a = 25 o c unless otherwise noted) notes : 1. t est conditions: i f = 0.5a, i r = -1.0a, i rr = -0.25a 2. measured at 1 mh z and applied reverse voltage of 4.0 volts dimensions in inches and (millimeters) 2003-7 operating and storage temperature range t j , t stg -55 to + 150 0 c ratings maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t a = 55 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) typical junction capacitance (note 2) symbol v rrm v dc i o i fsm c j v rms amps 1.0 30 15 amps pf units volts volts volts 12 50 maximum reverse recovery time (note 1) trr 75 nsec at rated dc blocking voltage t a = 25 o c characteristics maximum full load reverse current average, full cycle .375 (9.5mm) lead length at t l = 55 o c v f symbol i r 5.0 100 uamps uamps maximum dc reverse current maximum instantaneous forward voltage at 1.0a dc volts units 50 35 50 100 70 100 200 140 200 600 420 600 1000 700 1000 800 400 280 400 300 210 300 rl101h rl102h rl103h rl104h rl105h rl106h rl108h rl107h 800 560 1.0 1.3 rl101h rl102h rl103h rl104h rl105h rl106h rl107h rl108h 1.7 1.0 ( 25.4 ) min. .166 ( 4.2 ) .205 ( 5.2 ) 1.0 ( 25.4 ) min. .107 ( 2.7 ) .080 ( 2.0 ) dia. .025 ( 0.6 ) .021 ( 0.5 ) dia.
rectron rating and characteristic curves ( rl101h thru rl108h ) fig. 6 - typical junction capacitance junction capacitance, (pf) reverse voltage, ( v ) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 rl101h~rl105h rl106h~rl108h t j = 25 fig. 1 - test circuit diagram and reverse recovery time characteristic 50 noninductive 10 noninductive d.u.t 25 vdc (approx) ( - ) ( - ) ( + ) ( + ) 1 non- inductive oscilloscope (note 1) pulse generator (note 2) notes: 1 rise time = 7ns max. input impedance = 1 megohm. 22pf. 2. rise time = 10ns max. source impedance = 50 ohms. trr +0.5a 0 -0.25a -1.0a 1cm set time base for 10/20 ns/cm ambient temperature ( ) fig. 2 - typical forward current derating curve average forward curent, (a) 2.0 1.0 0 25 50 75 100 125 150 175 0 single phase half wave 60hz resistive or inductive load fig. 4 - typical instantaneous forward instantaneous forward current, (a) instantaneous forward voltage, (v) 10 1.0 .1 .01 .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 pulse width = 300us 1% duty cycle t j = 25 600 / 800/ 1000v 50 / 100 / 200v 300 / 400v fig. 3 - typical reverse characteristics instantaneous reverse current, (ua) percent of rated peak reverse voltage, (%) t j = 25 t j = 100 t j = 150 100 10 1.0 .1 .01 40 0 20 60 80 100 120 140 fig. 5 - maximum non-repetitive forward surge current peak forward surge current, (a) number of cycles at 60hz 50 40 30 20 10 0 1 2 10 20 40 100 8.3ms single half sine-wave (jedec method) 468 characteristics
|
